Voltage Divider Calculator
Two resistors, one lower voltage — plus the loaded-divider effect and a standard-value resistor picker.
Calculate
Fields accept plain numbers or formulas like 12000/2.
Enter any three values — input voltage, R1, R2 or output voltage — and the fourth is calculated.
All four values are needed: a load resistor RL in parallel with R2 pulls the output down.
Give the input voltage, the target output and R2 — the picker finds the nearest standard E12 resistor for R1 and the actual output it produces.
| Input voltage (Vin) | 12.0000 V |
| Resistance R1 | 1,000.0000 Ω |
| Resistance R2 | 1,000.0000 Ω |
| Output voltage (Vout) | 6.0000 V |
| Divider current (I) | 0.006000 A |
| Power in R1 | 0.036000 W |
| Power in R2 | 0.036000 W |
| Ratio Vout ÷ Vin | 0.5000 |
| Effective lower resistance (R2‖RL) | — Ω |
| Output voltage, loaded | — V |
| Output voltage, unloaded | — V |
| Voltage drop from loading | — V |
| Total current | — A |
| Current through R2 | — A |
| Current through load | — A |
| Power in load | — W |
| Ideal R1 (exact) | — Ω |
| Nearest E12 R1 | — Ω |
| Target output | — V |
| Actual output with E12 R1 | — V |
| Error from target | —% |
Working
- Vout = Vin × R2 ÷ (R1 + R2) = 12 × 1000 ÷ (1000 + 1000) = 6 V
- I = Vin ÷ (R1 + R2) = 0.006 A
- P1 = I² × R1 = 0.036 W; P2 = I² × R2 = 0.036 W
How to Use the Voltage Divider Calculator
Three modes cover the three divider questions. Basic solves one missing value: enter any three of input voltage, R1, R2 and output voltage. Loaded adds a load resistor across the output and shows the real voltage once the load draws current. The E12 picker chooses a buyable resistor: enter the input voltage, the target output and R2, and it returns the nearest standard E12 value for R1 plus the actual output that value produces. Every mode shows the divider current and the power in each resistor, so ratings are easy to check before building.
The Voltage Divider Rule
Two resistors in series share the supply voltage in proportion to their resistances, because the same current flows through both. The output, taken across the lower resistor R2, is:
The same current flows through R1 and R2: I = Vin ÷ (R1 + R2). The power in each resistor is I² × R — the upper resistor wastes power as heat, which is the price of the divider’s simplicity. Equal resistors split the voltage exactly in half; a 1 kΩ upper and 1 kΩ lower resistor across 12 V give 6 V out, with 6 mA flowing and 36 mW in each resistor.
Worked Examples
Example 1 — 12 V down to 6 V
Two 1 kΩ resistors across a 12 V supply.
Step 1: Vout = 12 × 1,000 ÷ (1,000 + 1,000) = 6 V.
Step 2: I = 12 ÷ 2,000 = 6 mA.
Step 3: P1 = P2 = 0.006² × 1,000 = 36 mW each — comfortably inside a 1/4 W rating.
Example 2 — 12 V down to 5 V with standard resistors
A 5 V rail is needed from 12 V, with R2 fixed at 5 kΩ. What R1?
Step 1: Ideal R1 = 5,000 × (12 − 5) ÷ 5 = 7,000 Ω.
Step 2: 7 kΩ is not a standard value; the nearest E12 value is 6.8 kΩ.
Step 3: Actual Vout = 12 × 5,000 ÷ (6,800 + 5,000) = 5.08 V — 1.7% above target, fine for most uses. The picker above does this in one step.
Example 3 — The loaded divider
The 12 V, 1 kΩ + 1 kΩ divider from Example 1 feeds a 1 kΩ load. What is the output now?
Step 1: R2 in parallel with the load: R2eq = 1,000 × 1,000 ÷ 2,000 = 500 Ω.
Step 2: Vout = 12 × 500 ÷ (1,000 + 500) = 4 V — the load pulls the output down from 6 V to 4 V.
Step 3: Total current = 12 ÷ 1,500 = 8 mA; 4 mA through R2 and 4 mA through the load. The loaded mode above shows all of this.
Choosing Resistor Values
Two tensions decide the values. Low resistances waste current and power — a 100 Ω + 100 Ω divider across 12 V burns 72 mA and 0.86 W just to make 6 V. High resistances are efficient but fragile: any load current steals a large share of the divider current and drags the output down, and high-impedance nodes pick up noise. A common compromise is a divider current around ten times the load current, typically 1–10 mA for signal work. For an ADC input that draws almost nothing, 10 kΩ resistors are typical; for a divider feeding a real load, the resistances come down until the load current is a small fraction of the divider current — or the divider is replaced by a regulator.
Power ratings follow from I² × R in each resistor. At 6 mA through 1 kΩ, each resistor dissipates 36 mW — a 1/4 W part has a seven-fold margin. At 60 mA the same resistors dissipate 3.6 W each and need power resistors with heatsinking. The results table shows both powers so the check takes seconds.
Standard Resistor Values (E12)
Resistors are sold in standard series, not arbitrary values. The E12 series has 12 values per decade — 1.0, 1.2, 1.5, 1.8, 2.2, 2.7, 3.3, 3.9, 4.7, 5.6, 6.8, 8.2 — times a power of ten, so 10 kΩ, 12 kΩ, 15 kΩ, 18 kΩ, 22 kΩ and so on. The spacing is about 20%, so the nearest E12 value is always within roughly 10% of any ideal value. With 10% tolerance parts, that is as close as the parts themselves are guaranteed, and the picker’s error figure shows exactly how far the real output lands from the target. Finer series exist — E24 (5%), E48 (2%), E96 (1%) — for circuits where 10% is too coarse, but E12 covers most divider work.
Common Mistakes
- Forgetting the load. A divider calculated unloaded is wrong the moment anything connects to the output. Always check the loaded value — the loaded mode exists for exactly this.
- Using a divider to power a load. Dividers are for signals and references, not power delivery. Any load current sags the output and wastes power as heat; a regulator or DC-DC converter is the right tool for power.
- Choosing resistors too large for the load. A 1 MΩ divider feeding a 100 kΩ input loses most of its voltage to the load. Keep the divider current at least ten times the load current.
- Choosing resistors too small for the supply. A 100 Ω divider across 12 V draws 60 mA and burns 0.72 W — fine for a power resistor, wasteful and hot for signal work.
- Ignoring resistor tolerance. Two 10% resistors can push the output several percent off the nominal value. For a reference voltage that must be accurate, use 1% parts or measure and trim.
- Expecting more out than in. A passive divider only splits the input. A higher output needs an active circuit — a boost converter, a charge pump or an amplifier.
My saved numbers reuse them in any calculator
Save a number once — like your rent or hourly rate — then just type its name instead of the number, in any calculator here. You can also type formulas like 5000 * 1.1 right into any box.
Saved only in this browser — nothing is sent to us.
Frequently Asked Questions
What is a voltage divider?
A voltage divider is two resistors in series across a voltage source. The same current flows through both, so the voltage splits in proportion to the resistances. The output, taken across the lower resistor R2, is Vout = Vin × R2 ÷ (R1 + R2). It is the simplest way to get a lower voltage from a higher one.
How do I calculate the output voltage of a voltage divider?
Multiply the input voltage by R2 and divide by the total resistance: Vout = Vin × R2 ÷ (R1 + R2). For example, 12 V across 1 kΩ and 1 kΩ gives Vout = 12 × 1000 ÷ 2000 = 6 V. Equal resistors split the voltage in half.
How do I choose R1 and R2 for a target output voltage?
Pick R2 first, then R1 = R2 × (Vin − Vout) ÷ Vout. For 12 V to 5 V with R2 = 5 kΩ, R1 = 5,000 × 7 ÷ 5 = 7,000 Ω. The nearest standard E12 value is 6.8 kΩ, which gives an actual output of 5.08 V — close enough for most uses. The picker on this page does this automatically.
Why does a load change the divider output voltage?
A load resistor RL in parallel with R2 lowers the effective lower resistance to R2eq = R2 × RL ÷ (R2 + RL), so the output drops: Vout = Vin × R2eq ÷ (R1 + R2eq). A 12 V divider with 1 kΩ + 1 kΩ gives 6 V unloaded but only 4 V with a 1 kΩ load. The rule of thumb: the load should draw less than about one tenth of the divider current for the output to stay close to the unloaded value.
What resistor values should a voltage divider use?
Low enough that the load current is small compared with the divider current, and high enough that the wasted current stays small. A common compromise is a divider current around 10 times the load current and in the 1–10 mA range for signal work. Also check power: P = I² × R in each resistor must stay below its rating — 1/4 W resistors are standard for small-signal dividers.
Can a voltage divider power a load?
Only very light loads. Any load current comes straight out of the divider, so the output voltage sags and the divider wastes power as heat. For real power delivery, use a voltage regulator or a DC-DC converter instead. Dividers are for signals and references — sensor outputs, ADC inputs, bias voltages — not for power.
What are E12 resistor values?
E12 is the standard series of 12 resistor values per decade: 1.0, 1.2, 1.5, 1.8, 2.2, 2.7, 3.3, 3.9, 4.7, 5.6, 6.8 and 8.2, times a power of ten. They are spaced about 20% apart, so the nearest E12 value is always within about 10% of any ideal value — and with 10% tolerance parts, that is as close as the parts themselves are guaranteed.
Why can the output never exceed the input voltage?
A passive divider only splits what is there: both resistors drop voltage in the same direction, so the output across R2 is always a fraction of the input. Getting a higher voltage needs an active circuit — a boost converter, a charge pump or an amplifier.