Watts Volts Amps Ohms Calculator
Any two of watts, volts, amps and ohms — the other two, solved instantly from the power wheel.
Calculate
Enter any two values and leave the other two blank. Fields accept plain numbers or formulas like 240/2.
| Voltage (V) | 120.0000 V |
| Current (I) | 0.5000 A |
| Resistance (R) | 240.0000 Ω |
| Power (P) | 60.0000 W |
Working
- I = P ÷ V = 60 ÷ 120 = 0.5 A
- R = V ÷ I = 120 ÷ 0.5 = 240 Ω
How to Use the Watts-Volts-Amps-Ohms Calculator
Enter any two of the four values — voltage in volts, current in amps, resistance in ohms, power in watts — and the other two appear instantly, with the working shown. The most common pair is the one on an appliance label: voltage and power. A 60 W bulb on 120 V mains draws 0.5 A and has a hot resistance of 240 Ω. Results update live as values change, so trying a 100 W bulb in the same socket immediately shows 0.83 A and 144 Ω.
The calculator works for DC circuits and for resistive AC loads (heaters, incandescent bulbs, toasters), where voltage and current stay in phase. For AC circuits with motors, transformers or capacitors, the current lags or leads the voltage and apparent power (VA) differs from real power (W) — the power calculator covers that case with a power factor input.
The Power Wheel: All Twelve Formulas
Voltage, current, resistance and power are linked by two equations — Ohm’s law (V = I × R) and the power law (P = V × I). Rearranging them gives twelve formulas, three for each quantity. The table below is the complete power wheel; the calculator applies the right one automatically for whichever pair is entered.
| Solve for | Formula 1 | Formula 2 | Formula 3 |
|---|---|---|---|
| Volts (V) | V = I × R | V = P ÷ I | V = √(P × R) |
| Amps (I) | I = V ÷ R | I = P ÷ V | I = √(P ÷ R) |
| Ohms (R) | R = V ÷ I | R = V² ÷ P | R = P ÷ I² |
| Watts (P) | P = V × I | P = V² ÷ R | P = I² × R |
Two of the formulas deserve a second look. P = V² ÷ R says power grows with the square of voltage: doubling the voltage across a fixed resistor quadruples the power. P = I² × R says power grows with the square of current: doubling the current through a wire quadruples the heat in it — which is why long-distance power lines run at very high voltage and low current, keeping I²R losses small.
Worked Examples
Example 1 — Watts to amps
A 1,500 W space heater runs on 120 V. How much current does it draw?
Step 1: I = P ÷ V = 1,500 ÷ 120 = 12.5 A.
Step 2: R = V ÷ I = 120 ÷ 12.5 = 9.6 Ω. A standard 15 A household circuit has little headroom left — running a second heater on the same circuit trips the breaker.
Example 2 — Amps to watts
A phone charger delivers 2 A at 5 V. How much power is that?
Step 1: P = V × I = 5 × 2 = 10 W.
Step 2: R = V ÷ I = 5 ÷ 2 = 2.5 Ω — the effective resistance of the phone’s charging circuit at that moment.
Example 3 — Resistance and power from voltage and current
A 9 V battery drives 90 mA through a resistor. Find the resistance and the power.
Step 1: Convert: 90 mA = 0.09 A.
Step 2: R = V ÷ I = 9 ÷ 0.09 = 100 Ω.
Step 3: P = V × I = 9 × 0.09 = 0.81 W. A standard 1/4 W resistor is not enough here — a 1 W part is the safe choice.
Everyday Appliances
| Appliance | Power | At 120 V | At 230 V |
|---|---|---|---|
| Phone charger | 10 W | 0.08 A | 0.04 A |
| LED bulb | 9 W | 0.075 A | 0.04 A |
| Incandescent bulb | 60 W | 0.5 A | 0.26 A |
| Laptop charger | 65 W | 0.54 A | 0.28 A |
| Microwave oven | 1,000 W | 8.3 A | 4.3 A |
| Hair dryer | 1,500 W | 12.5 A | 6.5 A |
| Space heater | 1,500 W | 12.5 A | 6.5 A |
| Electric kettle | 2,000 W | 16.7 A | 8.7 A |
| Electric oven | 2,400 W | 20 A | 10.4 A |
| Air conditioner | 3,500 W | 29 A | 15.2 A |
The pattern is the point: the same wattage draws roughly half the current at 230 V as at 120 V, because current is power divided by voltage. That is why 230 V countries can run a 2 kW kettle on an ordinary socket while a 120 V kettle of the same power needs a dedicated 20 A circuit.
Watts vs Volt-Amps
In a DC circuit, watts and volt-amps are the same number: P = V × I either way. In an AC circuit with an inductive or capacitive load — a motor, a transformer, a fluorescent ballast — the current is out of phase with the voltage, and apparent power (S, in VA) exceeds real power (P, in W). The ratio is the power factor: P = S × PF. A 1,000 VA motor at PF 0.8 delivers 800 W of real power and draws 200 VAR of reactive power. Breakers, cables and transformers must be sized for the volt-amps, not the watts, because the current — and the heating it causes — follows the apparent power.
Common Mistakes
- Forgetting unit prefixes. 20 mA is 0.02 A; 4.7 kΩ is 4,700 Ω; 2.2 kW is 2,200 W. A missed prefix moves the answer by a factor of 1,000 — the most common error in these calculations.
- Using a bulb’s cold resistance. A filament’s resistance rises several-fold as it heats. The resistance computed from the rated watts and volts is the hot resistance; the cold resistance measured with a multimeter is far lower.
- Adding currents across different voltages. A 10 W charger at 5 V draws 2 A on the low-voltage side but only about 0.1 A from the 120 V mains (plus losses). Currents only add when the voltages match.
- Reading power as energy. Watts are a rate; watt-hours are an amount. A 60 W bulb running for 10 hours uses 600 Wh = 0.6 kWh of energy. The bill charges for kWh, not watts.
- Assuming the label wattage is the draw. Some appliances list output power (a 1,000 W microwave delivers 1,000 W to the food but draws about 1,400 W from the wall). Check whether the label says input or output power before sizing a circuit.
My saved numbers reuse them in any calculator
Save a number once — like your rent or hourly rate — then just type its name instead of the number, in any calculator here. You can also type formulas like 5000 * 1.1 right into any box.
Saved only in this browser — nothing is sent to us.
Frequently Asked Questions
How do I convert watts to amps?
Divide watts by volts: I = P ÷ V. A 60 W bulb on 120 V draws 60 ÷ 120 = 0.5 A. The same bulb on 230 V draws only 60 ÷ 230 = 0.26 A — which is why mains current differs between countries for the same appliance.
How do I convert amps to watts?
Multiply amps by volts: P = V × I. A 2 A phone charger at 5 V delivers 10 W. A 13 A circuit at 230 V can supply up to 13 × 230 = 2,990 W before the breaker trips.
How do I find resistance from voltage and power?
R = V² ÷ P. A 60 W bulb rated for 120 V has R = 120² ÷ 60 = 240 Ω. The same 60 W bulb rated for 230 V has R = 230² ÷ 60 = 882 Ω — the two bulbs are not interchangeable.
What is the power wheel?
The power wheel (or Ohm’s law wheel) is a circular chart of the twelve formulas linking V, I, R and P. Each quantity has three formulas: V = I × R, V = P ÷ I, V = √(P × R); I = V ÷ R, I = P ÷ V, I = √(P ÷ R); R = V ÷ I, R = V² ÷ P, R = P ÷ I²; P = V × I, P = V² ÷ R, P = I² × R. This calculator applies them automatically.
Why do I need only two values?
Voltage, current, resistance and power are linked by two independent relations — Ohm’s law (V = I × R) and the power law (P = V × I). Two equations, four unknowns: fixing any two determines the rest. A third value would either agree (redundant) or contradict the first two.
What is the difference between watts and volt-amps?
Watts measure real power — the energy actually used. Volt-amps measure apparent power — voltage times current. In DC circuits they are identical. In AC circuits with reactive loads, apparent power (VA) exceeds real power (W), and the ratio is the power factor: W = VA × PF.
How many amps is 1000 watts?
It depends on the voltage: I = P ÷ V. At 120 V, 1,000 W draws 8.33 A. At 230 V, the same 1,000 W draws 4.35 A. At 12 V, it draws 83.3 A — which is why high-power 12 V wiring needs very thick cable.